Тест складається із 80 випадкових питань.
Усього питань на цю тему: 115
When should a crew member joining a ship for the first time be given some training and instructions in the use of the ship’s fire-fighting appliances?
As soon as possible but not later than 2 weeks after he joins the ship.
As soon as possible but not later than 2 days after he joins the ship.
As soon as possible but not later than 24 hours after he joins the ship.
Your vessel is involved in a collision with another vessel. What should you as Master tell the Master on the other vessel?
There should be no communication with the other vessel.
Explain your actions prior to the collision and request details of actions taken by the other vessel which resulted in the collision.
Ask if there is any assistance required by the other vessel.
Name; Port of registry; Port of destination of your vessel.
Which of the following channels and modes should be used when initiating a distress alert transmission?
Channel 13 Radiotelephony and channel 16 DSC.
Channel 6 Radiotelephony.
When conducting a risk assessment for a shipboard work activity, the two elements to be considered are:
The time available to complete the task and the resources to hand.
The potential severity of harm and the likelihood that harm will occur.
The available manpower and their experience in this type of work.
The chance of an incident re-occuring and the potential effects of an loss.
What type of dynamic forces may cause indent in plating on forecastle deck and main deck in way of pillars inside forecastle?
Pressure forces caused by green water on deck.
Forces created by waves on the forecastle.
Slamming in way of flat bottom forward of light draught.
The steps of the embarkation ladder used must be proportioned as it follows:
Length = 580 mm, breadth = 165 mm, depth = 30 mm.
Length = 480 mm, breadth = 115 mm, depth = 25 mm.
Length = 380 mm, breadth = 145 mm, depth = 20 mm.
Length = 280 mm, breadth = 85 mm, depth = 10 mm.
Additional lashings on general cargoes must be considered when:
The density of the water.
Passing trough the Tropical Zone in winter months.
Passing through the Summer Zone in winter months.
Who will have the authority to take charge and make appropriate decisions in the event of a vessel emergency when transiting the Panama Canal?
The Panama Canal Authority.
Messages sent via INMARSAT-C are charged:
On the number of kilobits of information transmitted per block of 256 bits.
On the basis of a 6 second minimum charge with 6 second incremental steps.
On the number of kilobits of information transmitted per block of 1 024 bits.
The steps of the embarkation ladder used must be spaced apart by a distance of:
Equally spaced, not less than 300 mm or more than 380 mm.
Equally spaced, not less than 200 mm or more than 280 mm.
Additional lashings on general cargoes must be considered when:
When passing through the Tropical Zone in winter months.
When heavy weather is anticipated for the planned voyage.
When passing through the Summer Zone in winter months.
With the onset of heavy weather.
For a search to be effective it must be:
Conducted by personnel with limited knowledge of the ship’s layout.
Inclusive of all personnel.
It is important for hatch coaming compression bars to be maintained in good order on a General Cargo Vessel so that:
So that hatch covers remain water tight.
So that water can drain out from the hatch coaming drains.
So that hatches can be properly sealed.
So that there is no steel contact between the hatch covers and hatch coaming.
Where is the Safety Certificates for ships to be kept?
What does ISM stand for?
The International Management Code for the Safe Operation of Ships and for Pollution Prevention.
International Safe Manning Certification.
Internal Ship Safety Management.
International Ship Measurement and Pollution Control.
Which of the following channels and modes should be used when initiating a distress alert transmission?
Channel 13 Radiotelephony, channel 16 DSC.
If for some reason a vessel does not comply with a Classification Society’s requirements, what can a surveyor issue to the vessel enabling it to sail to the next port or for a period of time?
A Notification of Deficiency.
A revised Class Notation.
A Notification of Detention.
Which of the following cargoes can normally be loaded next to each other in the same space of a General Cargo vessel?
Drums of cement and steel pipes.
Drums of cement and bagged milk powder.
Pallets of pesticides and bagged grain.
Which of the following two digits codes is used to obtain medical assistance?
What is the world-wide system operated by the US Coast Guard exclusively in support of search and rescue operations?
The Automated Mutual-Assistance Vessel Rescue (AMVER) System.
The International Search and Rescue Coordination System.
The US Command and Control Rescue (USCOMR) Service.
The Worldwide Maritime Mutual Assistance Programme (WMMAP).
Which of the options best describes how a “Balanced Rudder” is constructed?
Part of the rudder area is forward of the turning axis, therefore reducing the load on the steering motor.
A rudder with equal rudder area forward and aft of the turning axis, the turning axis being at the geometrical centre of the rudder area.
A rudder which is operated by two steering motors providing equal amounts of thrust to the rudder.
A rudder with an additional flap attached the training edge to improve the rudder efficiency.
A general cargo with a large metacentric height (GM) would be expected to have:
A fast roll period and small righting levers (GZ Levers).
A fast roll period and large righting levers (GZ Levers).
A long roll period and large righting levers.
A long roll period and small righting levers (GZ Levers).
The steps of the embarkation ladder used use d must be proportioned as it follows:
Length = 480 mm, breadth = 115 mm, depth = 25 mm.
Length = 280 mm, breadth = 85 mm, depth = 10 mm.
Length = 580 mm, breadth = 165 mm, depth = 30 mm.
Length = 380 mm, breadth = 145 mm depth = 20 mm.
For security purposes, the IMDG Code should be read in conjunction with the:
Chapter XI-2 of SOLAS and Part A of the ISPS Code.
IMO NVIC 24 and 46 CFR 2.05.
Part B of the ISPS Code and Chapter II of the Maritime Transport and Offshore Facilities Act.
Which of the following two digits codes is used to obtain maritime assistance?
A general cargo with a large metacentric height (GM) would be expected to have:
A fast roll period and large righting levers (GZ Levers).
A fast roll period and small righting levers (GZ Levers).
A long roll period and large righting levers.
To maintain good relationship among the crew on board a vessel, one must be:
Understanding, Co-operative, and have respect from both sides.
Strict and authoritative while giving orders.
Give authority to others.
Polite and diplomatic while talking to crew members.
The MF/HF-transceiver on board is tuned to the assigned frequency of a station. To make this connection on the following mode is is used:
According to Rule 26 of the International Regulations for Preventing Collisions and the illustrated lights, what type of vessels are they?
These are two vessels engaged in fishing (pair trawling), showing the additional volutary signals for hauling nets.
This is a vessel engaged in towing a disabled tow, restricted in its ability to manoeuvre, with a searchlight used to highlight the location of the tow.
These are two vessels engaged in fishing (using purse-seine gear). The searchlights are simply working lights.
These are two vessels engaged in fishing (pair trawling), showing the additional voluntary signals for shooting nets.
Which one of the listed items has to be included in a distress message?
Weather in immediate vincinity.
Identification of the ship.
When should a crew member joining a ship for the first time be given some training and instructions in the use of the ship’s fire-fighting appliances?
As soon as possible but not later than 2 weeks after he joins the ship.
As soon as possible but not later than 24 hours after he joins the ship.
The operating mode of a pyrotechnic signal depends essentially on:
Instructions or diagrams printed on its casing by the manufacturer.
The fact that the user is on board a liferaft, a lifeboat or ship.
The weather conditions of the moment.
A definite standard process.
For security purposes, the IMDG Code should be read in conjunction with the:
Chapter XI-2 of SOLAS and Part A of the ISPS Code.
Chapter V of SOLAS and Annex II of MARPOL.
Part B of the ISPS Code and Chapter II of the Maritime Transport and Offshore Facilities Act.
IMO NVIC 24 and 46 CFR 2.05.
What is the priority for the ship’s management team when fire breaks out?
The ship’s management team must organise the fire teams and then the teams have to rescue missing personnel.
The ship’s management team must call the nearest fire brigade and police station.
The ship’s management team and the crew must evacuate the ship.
The ship’s management team must fight the fire and then call the fire teams.
If the speed of a vessel through the water is HALVED, how will this effect squat?
The squat effect will be reduced to a quarter of its original value.
There will be very little change to the effects of Squat.
There will be a significant change in the reduction of underkeel clearance, but the amount varies from ship to ship.
The squat effect will also be halved.
Messages sent via INMARSAT-C are charged:
On the number of kilobits of information transmitted per block of 256 bits.
On the basis of a three minute minimum charge with one minute incremental steps.
On the number of kilobits of information transmitted per block of 1 024 bits.
On the basis of a six second minimum charge with six second incremental steps.
Which one of the following items has to be included in an abandon ship drill according to SOLAS regulations?
Checking that life-jackets are correctly donned.
Launching and recovery of a survival craft.
Manoeuvring the lifeboat in the water.
Starting and operating radio life-saving appliances.
On a General Cargo vessel, a 16T derrick should be tested to a proof load of:
An Oil Record Book, Part 1, shall be provided to every ship of 400 tons gross tonnage and above to record machinery space operations.Out of below mentioned operations, it is compulsory to record:
Bunkering of bulk lubricating oil.
Discharge of water from Aft, Peak Tank.
Transfer of oil from settling – to daytank.
What is the main theme of modern safety practice?
Use the same practice that has been in place for some time.
Health & Safety at Work Act.
Consult the chief officer before commencing work.
Making use of Risk Assessment as a means to improving safety.
Which of the following is the correct minimum carriage requirement for a ship of more than 300 gross tons and operating in area A1:
1 VHF RT + DSC+ DSC watch receiver – 1 or 2 SART – 1 NAVTEX or 1 EGC receiver– 2 or 3 VHF portable – 1 EPIRB.
1 VHF RT + DSC + DSC watch receiver – 1 NAVTEX or 1 EGC reveiver – 2 or 3 VHF portable – 1 EPIRB – 1 MF RT + DSC + DSC watch reveiver – 1 INMARSAT A, B or C and 1 HF RT + DSC + DSC watch reveiver.
1 or 2 SART – 1 NAVTEX and/or 1 EGC receiver and/or 1 HF NBDP watch receiver – 2 or 3 VHF portable – 1 1 HF RT + DSC + DSC watch reveiver.
Which of the following cargoes can normally be loaded next to each other in the same space of a General Cargo vessel?
Drums of cement and steel pipes.
Drums of cement and bagged milk powder.
Pallets of pesticides and bagged grain.
Rolls new carpets and drums lubricating oils.
A General Cargo vessel has a 50 tonne SWL heavy lift derrick and a load of 48 tonnes is to be loaded. The lifting gear of slings and spreader bar weighs 4 tonnes. In this case, it would be correct to state that:
The load cannot be loaded because the combined weight of the load and the lifting gear must at least 10 % less than the SWL of the derrick.
The load can be loaded because the load itself is less than the SWL of the derrick.
The load can be loaded because the SWL can sometimes be exceeded by small amounts in cargo operations.
The load cannot be loaded because the combined weight of the load and the lifting gear will exceed the SWL by two tonnes.
What mode must be used on the MF/HF transmission, when transmitting a telex-message:
A message is sent to a fax-machine. However the message cannot be delivered by the land earth station. The land earth station will:
Will only send a non-delivery notification (NDN) to the sender if so requested by him.
Automatically send a non-delivery notification (NDN) to the sender.
Never send a non-delivery notification (NDN) if a fax message to the sender. The sender to verify if the message was received.
On a General Cargo vessel, a 16T derrick should be tested to a proof load of:
The operating mode of a pyrotechnic signal depends essentially on:
The fact that the user is on board a liferaft, a lifeboat or ship.
Instructions or diagrams printed on its casing by the manufacturer.
The weather conditions of the moment.
A definite standard process.
What type of dynamic forces may cause indent in plating on forecastle deck and main deck in way of pillars inside forecastle?
Forces created by waves on the forecastle.
Pressure forces caused by green water on deck.
Slamming in way of flat bottom forward of light draught.
Impact pressure forces in way of abrupt or flared bow.
If for some reason a vessel does not issue comply with vessel a Classification requirements, what can a surveyor to the enabling it Society’s to sail to the next port or for a period of time?
A Notification of Deficiency.
A revised Class Notation.
Which of the following is the correct minimum carriage requirement for a ship of more than 300 gross tons and operating in area A1:
1 VHF RT + DSC + DSC watch receiver – 1 or 2 SART – 1 NAVTEX or 1 EGC receiver – 2 or 3 VHF portable – 1 EPIRB.
1 VHF RT – 1 or 2 SART – 1 NAVTEX or 1 EGC receiver – 2 or 3 VHF portable – 1 EPIRB.
1 VHF RT + DSC + DSC watch receiver – 1 or 2 SART – 1 NAVTEX or 1 EGC receiver – 2 or 3 VHF portable.
What is the world-wide system operated by the US Coast Guard exclusively in support of search and rescue operations?
The Automated Mutual-Assistance Vessel Rescue (AMVER) System.
The Worldwide Mutual Assistance Programme (WMMAP).
The US Command and Control Rescue (USCOMR) Service.
At the entrance to the space where batteries are stored on board the following notice must be fitted:
No entry with naked light and/or flame.
The DSC-controller display the following: DOO: 244562000 CH16; S distress sinking. After receiving this DSC message the following is done immediately:
Listen out on VHF channel 16.
Send a “distress alert relay”.
Give a “DSC-acknowledgement”.
Steel coils when loaded on a General Cargo ship tend to be subjected to:
Chemical reactions between the steel banding and outer envelope.
Prior to loading general cargo on a General Cargo vessel, with regard to lashing wires, terminations, shackles, turnbuckles, pad eyes and D rings etc., you must make sure that:
They must all be certified and be visually inspected for any apparent damage.
They must all be visually inspected.
They must all be certified.
If W = Displacement, L = length, B = Breadth, D = depth of vessel, Cb = Block Coefficient, Cw = Coefficient of Waterplane, RD = Relative Density, then:
What is the main theme of modern safety practice?
Making use of Risk Assessment as a means to improving safety.
Consult the chief officer before commencing work.
Health & Safety at Work Act.
Use the same practice that has been in place for some time.
Which of following are security duties?
Calibration of security equipment.
Checking ID of visitors onboard.
Where is OPA-90 applicable?
Within 200 nm of US waters including Guam, Hawaii, Alaska and San Juan.
200 nm off coast of California.
DG placards shall be located on a freight container:
One on each end and one on each side.
One of the back end and one on one of the sides (only).
The MF/HF-transceiver on board is tuned to the assigned frequency of a station. To make this connection the following mode is used:
How often must inspection of proper working of the EPIRB’s and SART’s take place on board? Once per:
Which of the following following requirements regarding on board stability data corresponds to pres present regulations? NSCL (4/12.1).
A calculation example showing the use of “KG” limitation curves.
A calculation example showing use of “GM” limitation curves.
Drawings and calculations documenting the stability of the ship, both in intact and all possible damage condition.
The majority of convensions adopted under the auspices of IMO fall into which of the three main categories:
Maritime Safety, Safety, Prevention of Marine pollution, Liability and compensation.
There are no connections that fall under IMO.
Which of the following requirements regarding on board stability data corresponds to present regulations? (NSCL 4/12.1).
A calculation example showing the use of “KG” limitation curves.
Drawings and calculations documenting the stability of the ship, both in intact and all possible damage condition.
A calculation example showing use of “GM” limitation curves.
Stability data produced by stability calculation instruments.
Steel coils when loaded on a General Cargo ship tend to be subjected to:
Chemical reactions between the steel banding and outer envelope.
Which of the following two digits codes is used to obtain maritime assistance?
The value of the GZ lever at small angles of heel on a General Cargo Vessel can be denoted by the formula:
KM – KG × Sin angle of heel.
KM – Corrected KG × Sin angle of heel.
KN – Corrected KG × Sin angle of list.
Which of following are security duties?
Calibration of security equipment.
Checking ID of visitors onboard.
Monitoring of restricted areas.
You are proceeding along a coastal route when you hear this signal. The visibility is severely restricted. What does the signal mean?
There is a vessel aground in the vicinity. She is more than 100 metres in length. She is sounding an additional warning to approaching vessels that they are “running into danger”.
There is a vessels aground in the vicinity. She is less than 100 metres in length. She is sounding an additional warning to approaching vessels to “navigate with extreme caution”.
There is a vessel at anchor in the vicinity. She is less than 100 metres in length. She is sounding an additional warning to approaching vessels that they are “running into danger”.
There is a vessel at anchor in the vicinity. She is less than 100 metres in length. She is sounding an additional warning to approaching vessels that they are “keep clear”.
Which of the following two digits codes is used to obtain medical advice?
The portable walkie talkies required to be carried by GMDSS regulations should have which channels as a minimum?
Which of the following is a ship MMSI?
Which one of the listed items has to be included in a distress message?
Identification of the ship.
Weather in immediate vincinity.
At the entrance to the space where batteries are stored on board the following notice must be fitted:
No entry with naked light and/or flame.
An Oil Record Book, Part 1, shall be provided to every ship of 400 tons gross tonnage and above to record machinery space operations. Out of below mentioned operations, it is compulsory to record:
Transfer of oil from settling – to daytank.
Discharge of water from Aft, Peak Tank.
Bunkering of bulk lubricating oil.
The main purpose of a hatch cover ventilator grill on a General Cargo vessel is:
To prevent sparks entering the cargo hold.
To act as a strength member inside the ventilation shaft.
To prevent moisture from entering the hold.
What possible reason could there be for the identification mark associated with a Racon not being visible on the radar screen?
All of the suggested answers.
The radar may be suppressing the mark with application of the Interference Rejection Control.
The racon may not be transmitting a pulse.
The transmitted radar frequency may not trigger the Racon transmitter.
Which of the following is a ship MMSI?
Which one of the following items has to be included in an abandon ship drill according to SOLAS regulations?
Checking that life-jackets are correctly donned.
Launching and recovery of a survival craft.
Manoeuvring the lifeboat in the water.